Hello,
I have I3 M201 with old GTM32 Rev B motherboard. I would like to configure Marlin firmware for it. Any chance to get pins information / circuit diagram for it?
GTM32 Rev B Board Schematic?
Re: GTM32 Rev B Board Schematic?
Hello.
Be careful, the GTM32 vB Controller may not be compatible with the successor to the GTM32 Pro vB.
All available diagrams are shown in the forum. Subforum Control board.
However, there is no schematic you need.
I will try to ask if it can be shared.
Be careful, the GTM32 vB Controller may not be compatible with the successor to the GTM32 Pro vB.
All available diagrams are shown in the forum. Subforum Control board.
However, there is no schematic you need.
I will try to ask if it can be shared.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Re: GTM32 Rev B Board Schematic?
vert - Thanks I will see if I can get that to run!
_kaktus_ - It would be great if anything for GTM32 Rev B board could be shared, thank you for checking.
_kaktus_ - It would be great if anything for GTM32 Rev B board could be shared, thank you for checking.
Re: GTM32 Rev B Board Schematic?
Hi.
Still awaiting an answer, about the schematics to the older version of the controller ...
Still awaiting an answer, about the schematics to the older version of the controller ...
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Re: GTM32 Rev B Board Schematic?
Hi,kaktus.
will ask the engineer, and send it to you.
will ask the engineer, and send it to you.
-Keep your mind and try to test it.
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: GTM32 Rev B Board Schematic?
Hi.
Thank you, William. You're always there for me.
Thank you, William. You're always there for me.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Re: GTM32 Rev B Board Schematic?
-Keep your mind and try to test it.
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: GTM32 Rev B Board Schematic?
TAAA DAAAA ...
.On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.
Re: GTM32 Rev B Board Schematic?
wow
bravo,kaktus!
bravo,kaktus!
-Keep your mind and try to test it.
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!
Re: GTM32 Rev B Board Schematic?
Hi, _Kaktus_
you could make the GTM32 rev B scheme available on the subforum control board
because the image is too small to read
Thank you
you could make the GTM32 rev B scheme available on the subforum control board
because the image is too small to read
Thank you