Klipper on A10T

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Klipper on A10T

Post by AndreasThaler » Wed Nov 13, 2019 7:53 am

Hi there,
I am new to Geeetech printers. Up to now, I only used my Ender 3 (and SparkMaker). I love using Klipper on my Ender 3 and want to use it now with my new A10T. But... pins for the extruders? Sensor type? Sensor pin? Anyone experience with that?

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Re: Klipper on A10T

Post by AndreasThaler » Mon Nov 25, 2019 8:05 am

Ok,
I see the .cfg for the A10M with:
step_pin: ar46
dir_pin: ar44
enable_pin: !ar12
for extruder 0

step_pin: ar49
dir_pin: ar47
enable_pin: !ar48
for extruder 1

BUT
I can´t find any documentation about the pins for extruder 2.
Help please!

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Re: Klipper on A10T

Post by AndreasThaler » Tue Nov 26, 2019 5:59 am

step 43
Dir 45
EN 41

A guy in the Geeetech 3D Printer User Club just answered.
Bruce Greenleaf

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Re: Klipper on A10T

Post by AndreasThaler » Tue Nov 26, 2019 8:14 am

He measured and installed Marlin 2.0.

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Re: Klipper on A10T

Post by AndreasThaler » Fri Dec 06, 2019 6:11 am

I am afraid, there is no working bootloader on my A10T :(

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Re: Klipper on A10T

Post by AndreasThaler » Tue Dec 10, 2019 11:41 pm

There IS a working bootloader on the A10T. You have to press the "reset"-button while flashing! Crazy!
But now, I installed Klipper. The pins for E2 ARE right!

AndreasThaler
Posts: 7
Joined: Wed Nov 13, 2019 7:49 am

Re: Klipper on A10T

Post by AndreasThaler » Wed Dec 11, 2019 12:22 am

Here the working printer.cfg
printer.zip
(2.02 KiB) Downloaded 802 times

Morris456
Posts: 1
Joined: Tue Aug 17, 2021 2:03 pm

Re: Klipper on A10T

Post by Morris456 » Tue Aug 17, 2021 2:06 pm

I liked the idea of keeping the mass in the center of the X carriage, and looking at alot of other direct drive upgrades had the motor to one side or the other.

The ender 3 has a smaller X carriage than the A10 so I designed one in Fusion.

The small electronics board is mounted on top of the extruder motor.
Kroger Eschedule

vabakij
Posts: 1
Joined: Tue Nov 16, 2021 3:49 pm

Re: Klipper on A10T

Post by vabakij » Tue Nov 16, 2021 3:50 pm

The board of the index has a field about the article anywhere at any time no matter you are in pain or happy but the presence of God is compulsory at that place. The marriage encounters are the facing of iv therapy phoenix all the time and at any place.

jintee
Posts: 2
Joined: Thu May 05, 2022 12:45 pm

Re: Klipper on A10T

Post by jintee » Thu May 05, 2022 12:47 pm

We have recently come to know about the error 3835 while watching on Smores.TV and Engageme.TV and we have set out to fix hideouttv error 3835 using some basic troubleshooting techniques.

Post Reply