GTM32 Rev B Board Schematic?

TheDuke
Posts: 6
Joined: Sat Jul 01, 2017 12:54 pm

GTM32 Rev B Board Schematic?

Post by TheDuke » Sun Nov 17, 2019 1:12 pm

Hello,

I have I3 M201 with old GTM32 Rev B motherboard. I would like to configure Marlin firmware for it. Any chance to get pins information / circuit diagram for it?

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GTM32 Rev B Board Schematic?

Post by _kaktus_ » Sun Nov 17, 2019 3:32 pm

Hello.
:mrgreen:

Be careful, the GTM32 vB Controller may not be compatible with the successor to the GTM32 Pro vB.

All available diagrams are shown in the forum. Subforum Control board.
However, there is no schematic you need. :roll:

I will try to ask if it can be shared.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

TheDuke
Posts: 6
Joined: Sat Jul 01, 2017 12:54 pm

Re: GTM32 Rev B Board Schematic?

Post by TheDuke » Sun Nov 17, 2019 3:40 pm

vert - Thanks I will see if I can get that to run!

_kaktus_ - It would be great if anything for GTM32 Rev B board could be shared, thank you for checking.

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GTM32 Rev B Board Schematic?

Post by _kaktus_ » Sat Nov 30, 2019 5:50 am

Hi.
:mrgreen:

Still awaiting an answer, about the schematics to the older version of the controller ...
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: GTM32 Rev B Board Schematic?

Post by William » Mon Dec 02, 2019 10:13 am

Hi,kaktus.
will ask the engineer, and send it to you.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GTM32 Rev B Board Schematic?

Post by _kaktus_ » Tue Dec 03, 2019 5:28 am

Hi.
:mrgreen:

Thank you, William. You're always there for me. :D
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: GTM32 Rev B Board Schematic?

Post by William » Tue Dec 03, 2019 9:05 am

:D
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GTM32 Rev B Board Schematic?

Post by _kaktus_ » Thu Dec 05, 2019 8:54 pm

TAAA DAAAA ...
GTM32_vB.jpg
GTM32_vB.jpg (308.05 KiB) Viewed 32604 times
.
:D
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: GTM32 Rev B Board Schematic?

Post by William » Fri Dec 06, 2019 5:44 pm

wow :lol:
bravo,kaktus!
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

colcolo
Posts: 1
Joined: Thu Mar 05, 2020 3:20 am

Re: GTM32 Rev B Board Schematic?

Post by colcolo » Wed Mar 18, 2020 6:43 pm

Hi, _Kaktus_
you could make the GTM32 rev B scheme available on the subforum control board
because the image is too small to read
Thank you

Post Reply