A10M Slic3r profile

Share your configuration profile, please specify your printer model and the slicer software.
leongy1717
Posts: 17
Joined: Tue Jun 11, 2019 6:12 pm

Re: A10M Slic3r profile

Post by leongy1717 » Mon Jul 08, 2019 4:20 pm

Very good of you to develop and share for ABS filament.

Need help on slic3r profile too for PA Nylon filament with manufacturer's tips below:

https://bit.ly/32gaHnh

Printing temperature : 230°C - 260°C depending on part and printer type
Print speeds : 18 mm/s first layer, then 28mm/s - 34mm/s
Heated bed of 110°C helps combat Nylon's warp
No cooling fans
Only use in well ventilated areas
Store dry when not in use, absorbs moisture

P.S. -- Few prints of octopus & A10M Fan Cover cannot raise Z-axis to above 1 mm, despite over 1 hour of printing.
Attachments
White Nylon.jpg
White Nylon.jpg (147.13 KiB) Viewed 20669 times
Octopus Start.jpg
Octopus Start.jpg (207.57 KiB) Viewed 20669 times
Imprints.jpg
Imprints.jpg (275.8 KiB) Viewed 20669 times

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: A10M Slic3r profile

Post by William » Mon Jul 08, 2019 4:23 pm

Hi, from your screenshot, the position of the z-axis is too low, causing the distance between the nozzle and the hot bed to be too close.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

leongy1717
Posts: 17
Joined: Tue Jun 11, 2019 6:12 pm

Re: A10M Slic3r profile

Post by leongy1717 » Mon Jul 08, 2019 6:52 pm

The octopus imprint on heat bed was from Z at 0.4 till 38.4 mm after 2 hrs 23 minutes of printing

(nylon was melting at extruder) but Z cannot rise above 1 mm.

What caused this please? Thanks.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: A10M Slic3r profile

Post by William » Mon Jul 08, 2019 7:04 pm

Hi, According to my query, the printing of nylon consumables is nozzles 225-260, hot beds 70-90.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

leongy1717
Posts: 17
Joined: Tue Jun 11, 2019 6:12 pm

Re: A10M Slic3r profile

Post by leongy1717 » Mon Jul 08, 2019 9:03 pm

Am okay with temperatures stated in your reply.

My query is why extruder cannot rise up above 1 mm from hot bed despite 38.4 mm shown on green LCD screen.
No 3D octopus was printed except only white nylon imprint left on hot bed, i.e. Z-axis cannot rise above 1 mm.

Same with A10M Fan Cover using black nylon filament.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: A10M Slic3r profile

Post by William » Tue Jul 09, 2019 9:01 am

Hi, Maybe the consumables melt in the Teflon tube, you can clean the nozzles and then print.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

leongy1717
Posts: 17
Joined: Tue Jun 11, 2019 6:12 pm

Re: A10M Slic3r profile

Post by leongy1717 » Tue Jul 09, 2019 2:00 pm

No clogging found when either White or Black Nylon filament was selected for 3D printing,
since they were oozing out from single extruder while reaching 260 deg C.

In fact, stringing of black PA occurred during printing of A10M Fan Cover as 2D iso 3D.

Query is how to overcome 2D printing to realistic 3D printing extruder cannot rise up above 1 mm
from hot bed despite 38.4 mm shown on green LCD screen.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: A10M Slic3r profile

Post by William » Tue Jul 09, 2019 2:45 pm

Hi, have you tried printing other models? Maybe a slicing error can make printing impossible.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

leongy1717
Posts: 17
Joined: Tue Jun 11, 2019 6:12 pm

Re: A10M Slic3r profile

Post by leongy1717 » Tue Jul 09, 2019 7:36 pm

Yes, both mini Octopus and A10M Fan cover on BOTH slic3r and Skeinforge produce same 2D results

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: A10M Slic3r profile

Post by William » Wed Jul 10, 2019 9:31 am

Hi, maybe you need to adjust the bed temperature and try to reduce the print speed and try again.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Post Reply