[PROBLEM] Cannot connect only to Repetier host

Post Reply
pedracinI.julien@gmail.com
Posts: 2
Joined: Wed Sep 29, 2021 9:07 am

[PROBLEM] Cannot connect only to Repetier host

Post by pedracinI.julien@gmail.com » Wed Sep 29, 2021 9:24 am

Hello, happy buyer of an A20T, I cannot connect to my computer from Repetier. The printer constantly reboots.

I tried through the Arduino monitor, the printer works normally when entering commands, also with Ultimake Cura software. I specify that I am in baud 250000, the drivers well installed otherwise I could not use other software with. I also installed Marlin 2.0 but it doesn't change anything if I reinstall the original Firmware provided by Geeetech. I also tested on another PC with an old version of Repetier, without change.. I'm out of ideas.

here is a copy of the log:

Code: Select all

02:42:55.774 : start
02:42:55.774 : Marlin bugfix-2.0.x
02:42:55.774 : echo: Last Updated: 2021-09-26 | Author: (none, default config)
02:42:55.774 : echo: Compiled: Sep 29 2021
02:42:55.774 : echo: Free Memory: 1832  PlannerBufferBytes: 1776
02:42:57.094 : echo:V85 stored settings retrieved (634 bytes; crc 44948)
02:43:01.608 : echo:SD card ok
02:43:01.608 : FIRMWARE_NAME:Marlin bugfix-2.0.x (Sep 29 2021 02:28:28) SOURCE_CODE_URL:github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:Geeetech A20T EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
02:43:01.608 : Cap:SERIAL_XON_XOFF:0
02:43:01.608 : Cap:BINARY_FILE_TRANSFER:0
02:43:01.624 : Cap:EEPROM:1
02:43:01.624 : Cap:VOLUMETRIC:1
02:43:01.624 : Cap:AUTOREPORT_POS:0
02:43:01.624 : Cap:AUTOREPORT_TEMP:1
02:43:01.624 : Cap:PROGRESS:0
02:43:01.624 : Cap:PRINT_JOB:1
02:43:01.624 : Cap:AUTOLEVEL:1
02:43:01.624 : Cap:RUNOUT:1
02:43:01.624 : Cap:Z_PROBE:1
02:43:01.624 : Cap:LEVELING_DATA:1
02:43:01.624 : Cap:BUILD_PERCENT:0
02:43:01.624 : Cap:SOFTWARE_POWER:0
02:43:01.624 : Cap:TOGGLE_LIGHTS:0
02:43:01.624 : Cap:CASE_LIGHT_BRIGHTNESS:0
02:43:01.624 : Cap:EMERGENCY_PARSER:0
02:43:01.624 : Cap:HOST_ACTION_COMMANDS:0
02:43:01.624 : Cap:PROMPT_SUPPORT:0
02:43:01.624 : Cap:SDCARD:1
02:43:01.624 : Cap:REPEAT:0
02:43:01.624 : Cap:SD_WRITE:1
02:43:01.624 : Cap:AUTOREPORT_SD_STATUS:0
02:43:01.639 : Cap:LONG_FILENAME:0
02:43:01.639 : Cap:THERMAL_PROTECTION:1
02:43:01.639 : Cap:MOTION_MODES:0
02:43:01.639 : Cap:ARCS:1
02:43:01.639 : Cap:BABYSTEPPING:1
02:43:01.639 : Cap:CHAMBER_TEMPERATURE:0
02:43:01.639 : Cap:COOLER_TEMPERATURE:0
02:43:01.639 : Cap:MEATPACK:0
02:43:01.646 : X:-5.00 Y:0.00 Z:0.00 E:0.00 Count X:-400 Y:0 Z:0
02:43:01.646 : echo:DEBUG:INFO,ERRORS
02:43:01.646 : Begin file list
02:43:01.646 : A20T/A10TA2~1.GCO 1107216
02:43:01.662 : A20T/A20T-CAT.GCO 34470210
02:43:01.746 : A20T/2EB43~1.SLI/27D93~1.USB/FT232/LINUX/USBDRI~1/LIBFTD~1.GZ 3758080
02:43:01.762 : A20T/2EB43~1.SLI/27D93~1.USB/FT232/LINUX/USBDRI~1/LIBFTD~2.GZ 3573760
Maybe someone will have encountered the same problem as me, thank you in advance for helping me.

pedracinI.julien@gmail.com
Posts: 2
Joined: Wed Sep 29, 2021 9:07 am

Re: [PROBLEM] Cannot connect only to Repetier host

Post by pedracinI.julien@gmail.com » Wed Sep 29, 2021 6:10 pm

Hello, Problem solved after two hard days.

In fact, all you have to do is remove the microSD card from the printer. Strange. If it can help other people.

Post Reply