Purchased a new A20m this week and im having huge issues.
When it first arrived a ran a calibration cube and a geeetech box print to begin checking everything was optimised these printed fairly well.
Then my 3d touch arrived so i set about installing it.
Since the firmware upgrade and 3d touch install this printer now is massively under extruding with every print looking like a fish net and being extremely brittle to the point it just crumbles when taking off the bed.
i have tried changing slicers( Easyprintlite, Cura) brand new filament, Different filament brands, only print with one filament, or 2, gradient print, formatting sd card, different stl files, higher/lower temps, higher flowrate (at 150% it improved slightly) slower speeds, different retraction settings, adjusting z distance closer or further away, restored all slicer settings to default and im getting no where.
Mainboard is the GT2560 V4.1
Firmware version - A20M_3DTouch_hw4.1_fw2.2(ONLY for GT2560 V4.1 series motherboard) V2.2
(have also tried Firmware For A20M(ONLY for GT2560 V4.1 series motherboard, Selectable 3Dtouch function) V2.3
As the flow rate at 150% improved it slightly should i keep increasing it?
Right now im wishing i had stuck with my ender 6 and got another one instead of venturing into dual extruders.
im fairly new to 3d printing so any help appreciated
A20M help needed
Jump to
- Update Announcement/Product Release
- Firmware
- 3D Printer
- ↳ Thunder
- ↳ Mizar Pro
- ↳ Mizar S
- ↳ Mizar
- ↳ Geeetech I3/DIY Printer Series
- ↳ FAQ-Geeetech I3/DIY Printer series
- ↳ Geeetech I3 Pro B
- ↳ Geeetech I3 Pro W
- ↳ Geeetech I3 Pro X
- ↳ Geeetech I3 Aluminum
- ↳ Geeetech I3 Aluminum Pro
- ↳ Geeetech I3 Duplicator 5
- ↳ Geeetech I3 Pro C
- ↳ Geeetech I3 M201
- ↳ Geeetech A10 Series
- ↳ A10T
- ↳ Geeetech A20 Series
- ↳ Geeetech A20
- ↳ Geeetech A20M
- ↳ A20T
- ↳ Geeetech A30 Series
- ↳ A30M
- ↳ A30 PRO
- ↳ Geeetech E180 Mini
- ↳ Geeetech MeCreator2
- ↳ GiantArm D200
- ↳ Geeetech Delta Series
- ↳ Geeetech DP200 Series
- 3D Printing Software
- ↳ Configuration Profiles Sharing
- ↳ Software
- ↳ Wifi Box
- ↳ Bug report
- ↳ Download
- Hardware
- ↳ 3D Printer Hardware
- ↳ Stepper Motor
- ↳ Control Board
- ↳ Extruder
- ↳ Hot bed
- ↳ LCD Panel
- ↳ Power Supply Unit
- ↳ Assembly
- ↳ Others
- ↳ Video about cleaning and replacing nozzles
- Print Quality
- Resoures Sharing
- Feedback&Suggestion
- Project Talent Show
- Other Discussion
- ↳ Leveling Guide
- ↳ Open Hardware
- ↳ Mods And Hacks
- ↳ Products FAQ
- ↳ Tips & Tricks
- ↳ Discuss & Help
- ↳ Windows
- ↳ MAC