Search found 380 matches

by Admin
Mon May 17, 2021 2:46 pm
Forum: Geeetech A20
Topic: A20 Augo home
Replies: 2
Views: 4011

Re: A20 Augo home

Hello, if you have changed the motherboard, have you tried to update the firmware? You can update the firmware on the official website of geeetech:
http://www.geeetech.com/
by Admin
Mon May 17, 2021 2:43 pm
Forum: Geeetech A30 Series
Topic: Control Box Issue
Replies: 0
Views: 173

Re: Control Box Issue

Hello, you can observe whether there are LED lights on the motherboard and power supply, and see if these two parts are okay. If you have a multimeter, you can measure whether the input and output voltage of the power supply is within the range. Since I don't know what printer specification you boug...
by Admin
Mon May 17, 2021 2:35 pm
Forum: A30 PRO
Topic: Receiving help and support from Geetech, or their forum
Replies: 3
Views: 271

Re: Receiving help and support from Geetech, or their forum

Hello, if there is a problem with your printer, please contact geeetech official through ticket, they will try to help you solve the problem.
Or you can tell your printer fault, and I will try my best to help you solve the problem.
by Admin
Mon May 17, 2021 2:29 pm
Forum: Geeetech A20M
Topic: No LCD
Replies: 1
Views: 152

Re: No LCD

Hello, the voltage of the screen is 5v, you can measure whether it is normal. In addition, you can also connect to the computer via USB to see if you can control the printer through the slicing software. If you can, there is no problem with the motherboard, just the screen. Otherwise, there is a pro...
by Admin
Fri May 14, 2021 1:47 pm
Forum: Geeetech E180 Mini
Topic: Error: hotend-0 Abnormal temperature detected! please check!
Replies: 2
Views: 392

Re: Error: hotend-0 Abnormal temperature detected! please check!

Hello, please carefully check the adapter plate on the extrusion head of your printer, and check whether the heating rod and thermistor wire are connected properly. This error is caused by poor contact and is easy to repair. :D
by Admin
Fri May 14, 2021 10:19 am
Forum: Print Quality
Topic: The stringing problem of printing PLA
Replies: 0
Views: 266

The stringing problem of printing PLA

If you print a multi-color model with stringing , you can try the following print file to see how the printing effect is.
by Admin
Tue May 11, 2021 9:44 am
Forum: Print Quality
Topic: petg Temperature tower
Replies: 0
Views: 258

petg Temperature tower

The best printing temperature of petg can be measured when printing this file, but it is necessary to manually set the temperature to 250°C when printing the first layer.
by Admin
Thu May 06, 2021 5:35 pm
Forum: Geeetech A30 Series
Topic: Shift in Y axis 50% through print
Replies: 9
Views: 642

Re: Shift in Y axis 50% through print

Hello, the reason for the layer shift may be the printing speed is too fast or the tightness of the belt. You can reduce the printing speed to 40mm/s, and tighten the belt appropriately to see if you can restore the layer shift. If the layer shift still occurs, it is recommended to update the firmwa...
by Admin
Thu May 06, 2021 5:27 pm
Forum: Geeetech A10 Series
Topic: Geetech Not Connecting
Replies: 1
Views: 273

Re: Geetech Not Connecting

Hello, please try to install the driver by referring to the link below. If it still does not work, it may be a problem with the motherboard. Please contact your seller to replace the motherboard.
http://www.geeetech.com/forum/viewtopic ... 974#p81974
by Admin
Wed Apr 28, 2021 4:20 pm
Forum: Geeetech E180 Mini
Topic: Temperature issue
Replies: 0
Views: 318

Re: Temperature issue

Hello, this may be a thermistor problem. It is best to use a multimeter to measure the resistance of the thermistor at room temperature. Whether it is around 90K ohms. You can replace these simple thermistors and heating rods first. The entire extrusion head dont needs to be replaced.