Search found 1417 matches
- Wed Jul 01, 2015 5:17 pm
- Forum: Firmware
- Topic: How to upload the firmware to Sanguinololu
- Replies: 43
- Views: 216207
Re: How to upload the firmware to Sanguinololu/GT2560
The extruders heat up 200 degrees...it goes through the entire test program, but through it all the extruders does not advance the filament or attempt to turn once... Neither one no mater what computer I use...so please send me the firmware that makes this thing work or direct me words a board that...
- Wed Jul 01, 2015 11:02 am
- Forum: Stepper Motor
- Topic: Y axis stepper motor issue
- Replies: 22
- Views: 29843
Re: Y axis stepper motor issue
Some thing you described is contradictory: After I press Auto Home all the axis return to the home position I mean they hit the switch and then stop which I guess is normal. Also when I hit the Home button for Y axis it goes all the way back but even after it hits the rear switch it won't stop right...
- Wed Jul 01, 2015 10:58 am
- Forum: Others
- Topic: Lots of problems
- Replies: 6
- Views: 9822
Re: Lots of problems
Somewhere of the extruder heating wire must be broken, because the resistance you get is infinitely great, please check the wire. Please make sure the cooling fan is working for the mosfet, without the fan, the mosfet will burn too. And please check somewhere of hot bed is short circuit, short circu...
- Wed Jul 01, 2015 10:31 am
- Forum: Control Board
- Topic: My Rumba my be fired?
- Replies: 12
- Views: 20019
Re: My Rumba my be fired?
These pins need jumper caps:
If the setting voltage of fan is 12V, plug the jumper cap to the slot highlighted in the picutre. If it's 24V, plug jumper cap to the bottom 2 pins.- Wed Jul 01, 2015 9:17 am
- Forum: Extruder
- Topic: How to clear nozzle when it's jammed
- Replies: 13
- Views: 87418
Re: How to clear nozzle when it's jammed
If the nozzle is not jammed, you can extrude the filament by hand all the time.
If you are using PLA, I suggest you can raise the temperature slightly to 210 degrees (usually 200 degrees is high enough).
If you are using PLA, I suggest you can raise the temperature slightly to 210 degrees (usually 200 degrees is high enough).
- Wed Jul 01, 2015 9:14 am
- Forum: Stepper Motor
- Topic: Motor DOA, extruders do not work
- Replies: 11
- Views: 16948
Re: Motor DOA, extruders do not work
Hi,TAMHAN
Here is it:
extruder 0
enable : PG0 (Pin51)
direction: PL4 (Pin39)
step: PL6 (Pin41)
extruder 1
enable : PL1 (Pin36)
direction: PL2 (Pin37)
step: PL0 (Pin35)
Here is it:
extruder 0
enable : PG0 (Pin51)
direction: PL4 (Pin39)
step: PL6 (Pin41)
extruder 1
enable : PL1 (Pin36)
direction: PL2 (Pin37)
step: PL0 (Pin35)
- Tue Jun 30, 2015 5:20 pm
- Forum: Software
- Topic: Error Max Temp Bed
- Replies: 15
- Views: 30482
Re: Error Max Temp Bed
Did you unplug the wires from mainboard to measure it?
What reading do you get when you measure another thermistor?
What reading do you get when you measure another thermistor?
- Tue Jun 30, 2015 5:07 pm
- Forum: Software
- Topic: Error Max Temp Bed
- Replies: 15
- Views: 30482
Re: Error Max Temp Bed
Yes, that's it.
- Tue Jun 30, 2015 5:06 pm
- Forum: Others
- Topic: Strange problem: printing moved to the edge?
- Replies: 3
- Views: 6072
Re: Strange problem: printing moved to the edge?
Access "Printer settings" to change some parameters:
- Tue Jun 30, 2015 4:39 pm
- Forum: Firmware
- Topic: EndStops problem
- Replies: 27
- Views: 41279
Re: EndStops problem
Are this 2 LEDs lit when you turn on the printer?
And please check the microstep of y motor: If you are using A4988, the number of jumper cap under A4988 should be 3.