Search found 6340 matches
- Fri Sep 18, 2020 9:56 am
- Forum: Geeetech A30 Series
- Topic: First layer problems
- Replies: 1
- Views: 4470
Re: First layer problems
Hello, in response to your question. There are several suggestions: 1.Try to adjust the filament diameter to 1.75mm. 2. Slightly increase the extrusion ratio. 3. Increase the filling percentage. 4. Change to a slicing software, sometimes the printing effect will be significantly improved. 5. You can...
- Thu Sep 17, 2020 5:18 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 Pro doesn't start up
- Replies: 1
- Views: 2494
Re: Geeetech A10 Pro doesn't start up
Hello, maybe there is a problem with your LCD wiring, you can unplug it and reinstall it, and fasten it with a cable tie. You can also try to connect to the computer to see if it can start normally.If possible, please also provide pictures to better solve your problem.
Regards
Regards
- Wed Sep 16, 2020 5:26 pm
- Forum: Geeetech A10 Series
- Topic: Setting Up Slicer Software For A10M?
- Replies: 1
- Views: 2781
Re: Setting Up Slicer Software For A10M?
Hello, if you want to get the slicing software configuration of A10M, you can log in to the geeetech official website, where there are configuration files for Cura and Repeter-host for download. :D https://www.geeetech.com/download.html?download_id=31 https://www.geeetech.com/download.html?download_...
- Wed Sep 16, 2020 10:34 am
- Forum: Geeetech A10 Series
- Topic: A10 Partcooling fan problem
- Replies: 3
- Views: 3797
Re: A10 Partcooling fan problem
Hello, if you have some questions about pwm fans, you can refer to the following post.
viewtopic.php?f=24&t=17886
Regards
viewtopic.php?f=24&t=17886
Regards
- Tue Sep 15, 2020 3:09 pm
- Forum: Geeetech A10 Series
- Topic: A10 Partcooling fan problem
- Replies: 3
- Views: 3797
Re: A10 Partcooling fan problem
Hello, maybe there is something wrong with your fan. If you need to replace the accessories, please consult the Ticket system on the Geeetech official website.
Regards
Regards
- Tue Sep 15, 2020 3:04 pm
- Forum: Geeetech A10 Series
- Topic: Motherboard voltaje adjustment
- Replies: 1
- Views: 2607
Re: Motherboard voltaje adjustment
Hello, according to the formula, I_TripMax= Vref/(8*Rs) the drive resistance is 0.1Ω, so your current is about 1.5A.
Regards
Regards
- Tue Sep 15, 2020 11:49 am
- Forum: Geeetech I3 Pro W
- Topic: Extruder problem
- Replies: 3
- Views: 11911
Re: Extruder problem
Hello, you can take a look at the link below, there are very detailed solutions.
viewtopic.php?f=19&t=18650
Regards
viewtopic.php?f=19&t=18650
Regards
- Mon Sep 14, 2020 5:49 pm
- Forum: Geeetech A30 Series
- Topic: A30 firmware.
- Replies: 64
- Views: 158634
Re: A30 firmware.
Hello, you need to download the driver from the link below so that your printer can be recognized by the computer. Afterwards, you can upload the firmware through cura or download the firmware kit. https://www.geeetech.com/download.html?download_id=40 Please download the item of CH340, download the ...
- Mon Sep 14, 2020 2:57 pm
- Forum: Geeetech I3 Pro W
- Topic: Extruder problem
- Replies: 3
- Views: 11911
Re: Extruder problem
Hello, you can remove the Teflon tube and dredge the extruder with fine wire.
The cause of the blockage may be that your extruder screws are too tight and can be loosened slightly. Or there is a blockage inside the extruder, which will return to normal after cleaning.
Regards
The cause of the blockage may be that your extruder screws are too tight and can be loosened slightly. Or there is a blockage inside the extruder, which will return to normal after cleaning.
Regards
- Mon Sep 14, 2020 2:50 pm
- Forum: Firmware
- Topic: Problems MAC OS Firmware Toolkit
- Replies: 3
- Views: 4507
Re: Problems MAC OS Firmware Toolkit
Hello, please try to open the main program directly in the compression software, or you can replace the compression software.
Regards
Regards