Hi,
My board was fautly checking with oscilloscope the oscillator I don't have any signal. Swapped oscillator but nothing, I fear you have same problem.
Marco
Search found 20 matches
- Fri Jan 22, 2016 1:12 am
- Forum: Firmware
- Topic: Reflash Bootloader on GT2560
- Replies: 37
- Views: 100054
- Wed Nov 25, 2015 3:15 pm
- Forum: Extruder
- Topic: Videos of MK8 Extruder assembly
- Replies: 6
- Views: 36689
Re: Videos of MK8 Extruder assembly
Hello there is a small hex screw next to the hole in the back but I tryed to turn clockwise the screw go inside the hole a lot but don't fix. Should I turn a lot more?
- Wed Nov 25, 2015 5:29 am
- Forum: Extruder
- Topic: Videos of MK8 Extruder assembly
- Replies: 6
- Views: 36689
Re: Videos of MK8 Extruder assembly
hello the heater and the thermistor move inside the hole out and in, can be fixed someway?
- Wed Nov 25, 2015 5:24 am
- Forum: LCD Panel
- Topic: Lcd problem when connected to ramps
- Replies: 3
- Views: 9172
Re: Lcd problem when connected to ramps
solved smart connector connectors are mounted reversed swapped cable now is ok
- Tue Nov 24, 2015 5:18 pm
- Forum: LCD Panel
- Topic: Lcd problem when connected to ramps
- Replies: 3
- Views: 9172
Re: Lcd problem when connected to ramps
Yes the firmware is correct your firmware for rakps board prusa b and it works very well when lcd disconnected.
Lcd is correctly configured in config.h same as gt2560 firmware
Lcd is correctly configured in config.h same as gt2560 firmware
- Tue Nov 24, 2015 4:11 pm
- Forum: LCD Panel
- Topic: Lcd problem when connected to ramps
- Replies: 3
- Views: 9172
Lcd problem when connected to ramps
Hello I have had a gt2560 with 2004 lcd. Gt2560 is brocken so I swapped with a standard ramps/2560. Ai have to buy a standard lcd adapter on ebay for connecting 2004 to ramps. When I connect the lcd ribbon Printer stop working and on pc I see a mintemp error reached. Lcd doesn't work but is correctl...
- Tue Nov 17, 2015 9:39 pm
- Forum: Software
- Topic: Adjusting belt length
- Replies: 1
- Views: 6025
Re: Adjusting belt length
change value in eeprom settings until your printer move 100mm when you command a 100mm x or y move. I did this on a trial by error
Marco
Marco
- Tue Nov 17, 2015 9:29 pm
- Forum: Firmware
- Topic: Firmware for geeetech 3D printers
- Replies: 388
- Views: 16777215
Re: firmware for geeeteh 3D printers
Hello,
is it possibile to update Marlin firmware downloading it from github and allineate config.h from your config and new Marlin firmware? Did you do some kind of code personalization in you firmware outside of config.h?
I am interested in RAMPS version.
Thanks
Marco
is it possibile to update Marlin firmware downloading it from github and allineate config.h from your config and new Marlin firmware? Did you do some kind of code personalization in you firmware outside of config.h?
I am interested in RAMPS version.
Thanks
Marco
- Mon Nov 09, 2015 9:49 pm
- Forum: Firmware
- Topic: Substitute gt2560 with mega 2560 ramps 1.4
- Replies: 5
- Views: 11390
Re: Substitute gt2560 with mega 2560 ramps 1.4
Done,
thank you, I am printing now.
thanks
thank you, I am printing now.
thanks
- Sat Nov 07, 2015 2:41 am
- Forum: Firmware
- Topic: Firmware for geeetech 3D printers
- Replies: 388
- Views: 16777215
Re: firmware for geeeteh 3D printers
hello in PI3B-ramps.rar there is not Marlin.ino how to compile?
thanks
thanks