TESTED! Chip works great. Thanks again!knut_ny wrote:A new one received today (apr.17) THX!
Text on top of chis is fully readable! (Far from chip shown above)
I'll test it as soon as I've finishes my project sending data via ordinary 'walkie-talkies' (using DTFM-chip 8880)
Search found 8 matches
- Thu Apr 19, 2012 6:27 am
- Forum: Open Hardware
- Topic: Defect mangetometer 5883L
- Replies: 7
- Views: 34807
Re: Defect mangetometer 5883L
- Wed Apr 18, 2012 6:17 am
- Forum: Open Hardware
- Topic: Defect mangetometer 5883L
- Replies: 7
- Views: 34807
Re: Defect mangetometer 5883L
A new one received today (apr.17) THX!
Text on top of chis is fully readable! (Far from chip shown above)
I'll test it as soon as I've finishes my project sending data via ordinary 'walkie-talkies' (using DTFM-chip 8880)
Text on top of chis is fully readable! (Far from chip shown above)
I'll test it as soon as I've finishes my project sending data via ordinary 'walkie-talkies' (using DTFM-chip 8880)
- Tue Apr 10, 2012 2:49 am
- Forum: Open Hardware
- Topic: Temperature sensor schematic needed
- Replies: 3
- Views: 9160
Re: Temperature sensor schematic needed
I guess thats easy. The LM35 has three lines: Ucc, gnd and analog out. Hold the TO92 facing you - pins down: Ucc-> 5V (left pin) gnd-> GND (right pin) Uout ->analog X (middle pin) (X=0..5) The voltage you get is 10mV / deg C (cannot measuser below freezing with this method) int val= analogRead(X); /...
- Tue Apr 10, 2012 2:28 am
- Forum: Open Hardware
- Topic: Mini168 5V/16MHz
- Replies: 3
- Views: 8663
Re: Mini168 5V/16MHz
MY TTL<->USB card had a jumper, which I had to remove to get it working.
(based om PL2303-chip)
Knut
(based om PL2303-chip)
Knut
- Wed Apr 04, 2012 5:40 pm
- Forum: Open Hardware
- Topic: Defect mangetometer 5883L
- Replies: 7
- Views: 34807
Re: Defect mangetometer 5883L
Photo of chip added.
Has the chip been overheated?
Has the chip been overheated?
- Sat Mar 31, 2012 12:26 am
- Forum: Project Talent Show
- Topic: Weight, Height and BMI - project using microcontroller
- Replies: 1
- Views: 14013
Weight, Height and BMI - project using microcontroller
Build a BMI measuring scale using these parts: A (defective) electronic bathroom scale for loadcells , microcontroller (Arduino?), Ultrasonic sensor (e.g. SR04), LCD-display (e.g.1602), dual Rail-to-Rail OpAmp (e.g. one TS912) , Resistors and connecting wire. The scale has a loadcell in each corner....
- Fri Mar 30, 2012 8:53 pm
- Forum: Open Hardware
- Topic: HMC5883L Triple Axis Compass problem
- Replies: 6
- Views: 18840
Re: HMC5883L Triple Axis Compass problem
..Forget to remove the pull-ups. 5k +- is OK (internal ones do NOT do the job) You are not the ony one with a problem. Here is the short version of my story: I have bought 2 pcs HMC5883L magnetometers. One works fine, the other is DOA. I have done all I possibly can do (exept altering the board) to ...
- Fri Mar 30, 2012 8:46 pm
- Forum: Open Hardware
- Topic: Defect mangetometer 5883L
- Replies: 7
- Views: 34807
Defect mangetometer 5883L
I have bought 2 pcs HMC5883L magnetometers. One works fine, the other is DOA. I have done all I possibly can do (exept altering the board) to deterime that I have a defective board. Visual (under microscope) inspection. Verified all connection lines point to point. It looks OK. I do not have the equ...