GT2560 V3.0 Pinout or how to burn bootloader

Post Reply
BamBam
Posts: 1
Joined: Mon Oct 08, 2018 10:09 am
Location: Germany

GT2560 V3.0 Pinout or how to burn bootloader

Post by BamBam » Mon Oct 08, 2018 10:12 am

Hallo together,

During a Firmware upload I lost connection...
Now the board is just beeping und im unable to upload any firmware.

How can I burn a bootloader on the board?
Where do I need to connect to?

Thank you
Using an A10
GT2560 v3.0 board

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by _kaktus_ » Fri Oct 26, 2018 5:55 am

Hello.
:mrgreen:

To do this you will need a programmer, e.g. USBASP.
Place photos of the controller board and I will do my best to show you in detail what and how.
;)
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Matrix110
Posts: 2
Joined: Wed Sep 19, 2018 11:08 pm

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by Matrix110 » Thu Nov 15, 2018 4:01 am

I have the same problem and have asked Tech support for help and got no reply! I mistakenly tried to load a Hex file WITH bootloader and now have no communication with the printer. It seems from everything I have read that the GT2560 Rev A & B had a SD Card connector you could use to flash a new bootloader but the V3 has no such connector. I could really use some help here! :oops:
Attachments
2018-11-14_145432.jpg
GT2560 V3 Pic 1
2018-11-14_145432.jpg (60.97 KiB) Viewed 13640 times
2018-11-14_145349.jpg
GT2560 V3 Pic 2
2018-11-14_145349.jpg (54.69 KiB) Viewed 13640 times

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by _kaktus_ » Thu Nov 15, 2018 5:19 am

Hi
:mrgreen:

Photos are of poor quality ... :(
Despite this, I saw one unsolderable connector on them. It is located next to the description of the controller board model. ;)

I suggest to check with the continuity tester where the leads are connected.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Matrix110
Posts: 2
Joined: Wed Sep 19, 2018 11:08 pm

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by Matrix110 » Thu Nov 15, 2018 8:01 am

I was hoping for a little more than that, like maybe someone that has flashed a bootloader to this board and can share the hookup.

But thanks anyway.

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by _kaktus_ » Thu Nov 15, 2018 1:55 pm

Hi
:mrgreen:

If this connector does not have the appropriate signals, there is no other output, you have to solder the wires to the terminals of the SD card slot :!:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

apak
Posts: 48
Joined: Fri Jul 20, 2018 4:01 pm

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by apak » Mon Nov 19, 2018 7:52 pm

where is Header 4 (TXD3-RXD3) located. can´t locate it at pictures? Is it P1?

BR365
Posts: 57
Joined: Mon Apr 16, 2018 7:24 pm

Re: GT2560 V3.0 Pinout or how to burn bootloader

Post by BR365 » Fri Mar 29, 2019 3:09 pm

vert wrote:
Fri Mar 29, 2019 1:07 pm
there is a full guide here on the forums on burning a boot loader to the gt2560 V3 should try searching before re-posting something that has been documented.
Instead of writing this long sentence, You could have written the link to the full guide. This would have been much more helpfull (even when I agree, that it is always recommended to use the search, but sometimes, you don't use the good search words). ;)

This is the link, I guess You are talking about: http://www.geeetech.com/forum/viewtopic ... 98&t=61850

Moritz

Post Reply