Heatbed randomly stops heating

Post Reply
Stocki83
Posts: 6
Joined: Mon Sep 17, 2018 2:27 pm

Heatbed randomly stops heating

Post by Stocki83 » Sat Nov 03, 2018 5:47 pm

Yes the Heatbed randomly stops heating and goes down To room temperature. There also comes a Message nozzle temp-0 a few Seconds after the heatbed lost its temperature. And then most stupid Thing.... The printer don t stop Printing😆.... Of course without extruding... Anyone got an Idea??? Ty for your Help.

Stocki83
Posts: 6
Joined: Mon Sep 17, 2018 2:27 pm

Re: Heatbed randomly stops heating

Post by Stocki83 » Sat Nov 03, 2018 5:48 pm

Firmware is the newest stabile.. btw :ugeek:

dekes1
Posts: 36
Joined: Sat Oct 20, 2018 11:33 pm

Re: Heatbed randomly stops heating

Post by dekes1 » Sun Nov 04, 2018 7:27 am

Nozzle temp error message usually means a problem with the hot end thermistor. Either the thermistor is broken or the wires routing from the thermistor are broken. Check for continuity from the motherboard all the way to the thermistor. If the wires are good, i'd suggest replacing the thermistor.

Stocki83
Posts: 6
Joined: Mon Sep 17, 2018 2:27 pm

Re: Heatbed randomly stops heating

Post by Stocki83 » Sun Nov 04, 2018 8:48 pm

Hi dekes i have checked the cable. I think there is something wrong. Everytime i Touch the cable the heatbed works again for a time...

SirSunshine
Posts: 15
Joined: Sun Sep 02, 2018 12:15 am

Re: Heatbed randomly stops heating

Post by SirSunshine » Thu Nov 29, 2018 9:16 am

Hi, did you ever find a solution to this? I having similar problems. The heatbed stops heating but the error message is "Nozzle 0-Temp" or something similar. (obviously wrong since that pops up even if I'm not heating the nozzle).

I'm suspicious that it could be the little heatbed mosfet board overheating/gone bad.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Heatbed randomly stops heating

Post by William » Thu Nov 29, 2018 1:47 pm

You can open the PSU box and you can get more details.
We need to refer it. :?
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Stocki83
Posts: 6
Joined: Mon Sep 17, 2018 2:27 pm

Re: Heatbed randomly stops heating

Post by Stocki83 » Fri Nov 30, 2018 5:42 am

Hi, there was a problem with the cable from Bord Inside to plug. And I think there also was a problem with the heatbed cable included the heatbed . Both things were resent by geeetech. After changing these parts.. The printer Worked for 20h without errors. Nice Support geeetech ty :D :D :D

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Heatbed randomly stops heating

Post by William » Fri Nov 30, 2018 9:16 am

:D
That's good!
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Post Reply