Page 4 of 5

Re: Easyprint software for WINDOWS

Posted: Fri Jan 04, 2019 9:19 am
by William
bertie wrote:
Sat Dec 29, 2018 3:03 pm
I solved it by manually downloading and installing Visual C++ Redistributable 2015 (X86 + X64) from Microsofts website and reinstalling EasyPrint. Installing C++ via EasyPrint installer did not work for me and on my machine was only version 2017 instead of 2015.
Thx for your feedback! ;)

Re: Easyprint software for WINDOWS

Posted: Sat Jan 05, 2019 5:19 am
by pepgra
Because the combo-box does not show the model A20M?

Re: Easyprint software for WINDOWS

Posted: Sun Jan 06, 2019 8:18 pm
by Bernhard
Hello,
I installed the Easyprint software. I can load the 3D-files but I cannot save it as G-code.
There comes following failure notice: File C:\Users\Bernhard\AppData\Roaming\easyprint\work\composition.gcode was not found.
How can I get this file?
I use Windows 7 and Easyprint 1.2.6
Best regards

Re: Easyprint software for WINDOWS

Posted: Mon Jan 07, 2019 12:35 am
by nvnazeer
Hi, where can i get a link for the latest version of easyprint software for windows.
Are there any issues if i use this with A10M

Thanks

Re: Easyprint software for WINDOWS

Posted: Thu Jan 10, 2019 1:55 am
by _kaktus_
Hello.
:mrgreen:


nvnazeer
Your question should not be asked at all. :roll:
The answer is in the first post of this topic.

If you are an attentive observer you will see a location there: https://www.geeetech.com/firmware/
As of today, the latest version has been announced 2018-09-06.

Re: Easyprint software for WINDOWS

Posted: Thu Jan 17, 2019 4:08 am
by Achim2019
Hi, I'm new here. I miss the download button for Easyprint Software, english version.
Thx in advance!

Re: Easyprint software for WINDOWS

Posted: Sat Feb 02, 2019 5:23 am
by WikiBrikoFix
For all that have problems with EasyPrint 3D: the correct installation procedure is

1) Remove all C++ Redistributable version 2015 and 2017
2) Manual install the C++ Redistributable 2015 for x86 and x64 downloaded from here
https://www.microsoft.com/en-us/downloa ... x?id=52685
3) Install EasyPrint 3D (custom install, deselect C++ 2015 Redistributable packages)
4) reinstall C++ Redistributable 2017 removed on step 1
https://support.microsoft.com/it-it/hel ... -downloads

I have done it, after many problems, and now EasyPrint run correctly, without cura engine error and save error.

bye!

Re: Easyprint software for WINDOWS

Posted: Wed Feb 13, 2019 1:22 pm
by William
WikiBrikoFix wrote:
Sat Feb 02, 2019 5:23 am
For all that have problems with EasyPrint 3D: the correct installation procedure is

1) Remove all C++ Redistributable version 2015 and 2017
2) Manual install the C++ Redistributable 2015 for x86 and x64 downloaded from here
https://www.microsoft.com/en-us/downloa ... x?id=52685
3) Install EasyPrint 3D (custom install, deselect C++ 2015 Redistributable packages)
4) reinstall C++ Redistributable 2017 removed on step 1
https://support.microsoft.com/it-it/hel ... -downloads

I have done it, after many problems, and now EasyPrint run correctly, without cura engine error and save error.

bye!
;)
Thanks for sharing your experience!

Re: Easyprint software for WINDOWS

Posted: Sat Mar 23, 2019 3:05 am
by schlulou
Is this software still being worked on or can it be considered abandoned? What's the latest version? Too many sources to keep track of. Forum, apache listing, download section etc. My Version has no idea the A10M exists...

Re: Easyprint software for WINDOWS

Posted: Tue Mar 26, 2019 2:22 pm
by William
schlulou wrote:
Sat Mar 23, 2019 3:05 am
Is this software still being worked on or can it be considered abandoned? What's the latest version? Too many sources to keep track of. Forum, apache listing, download section etc. My Version has no idea the A10M exists...
Geeetech official won't updates EP, I recommended you to use Cura, Slic3r, etc.