Geeetech Prusa i3 Aluminum - Board Sanguinololu Rev 1.3a - Firmware?

[mbeach1116]

Where and how do I update the firmware for this version ?Geeetech Prusa i3 Aluminum - Board Sanguinololu Rev 1.3a

[William]

Hi, you can refer to this:viewtopic.php?f=20&t=17046

[mbeach1116]

Hi, you can refer to this:viewtopic.php?f=20&t=17046

I saw this post but dont understand which to use, etc.

[William]

Hi, you can refer to this:viewtopic.php?f=20&t=17046

I saw this post but dont understand which to use, etc.

Hi, you need to choose to download according to your model and motherboard corresponding type,
Then upload it using Arduino.

[mbeach1116]

Hi, you can refer to this:viewtopic.php?f=20&t=17046

I saw this post but dont understand which to use, etc.

Hi, you need to choose to download according to your model and motherboard corresponding type,
Then upload it using Arduino.

I understand that. How do I know which model and motherboard I have?

[William]

I saw this post but dont understand which to use, etc.

Hi, you need to choose to download according to your model and motherboard corresponding type,
Then upload it using Arduino.

I understand that. How do I know which model and motherboard I have?

Hi, your model is i3 aluminum
You need to download it from the corresponding firmware,
Motherboard, you can check your motherboard,
The corresponding model is written on it.

I hope this can help you.

[mbeach1116]

Hi, you need to choose to download according to your model and motherboard corresponding type,
Then upload it using Arduino.

I understand that. How do I know which model and motherboard I have?

Hi, your model is i3 aluminum
You need to download it from the corresponding firmware,
Motherboard, you can check your motherboard,
The corresponding model is written on it.

I hope this can help you.

How do I know which to use? Here is the options from the link you provided above.

3) Firmware for Aluminum I3
For sanguinololu, you need to copy the folder named "sanguino" to the folder "hardware" of Arduino IDE.
The "sanguino" folder:
sanguino.zip
(209.25 KiB) Downloaded 3767 times
Download this file and unzip it and move it to the folder "hardware".
1 for sanguinololy.jpg
1 for sanguinololy.jpg (34.93 KiB) Viewed 320440 times
Then you can use the Arduino IDE 1.0.1 to upload the firmware as the link:
viewtopic ... 20&t=16433
For the old aluminum i3(with printed extruder bracket and gear), use the firmware below:
aluminum I3 Ramps 1.4
PI3_Ramps14固件.rar
(199.43 KiB) Downloaded 3849 times
aluminum I3 sanguinololu
PI3_Sanguinololu固件.rar
(229.44 KiB) Downloaded 4069 times
For the full aluminum I3, use the firmware here:

for the upgraded kit using lead screw
Plusa_I3_A_sanguinololu(for the upgraded kit using lead screw).zip
(242.47 KiB) Downloaded 3749 times
aluminum I3 Ramps 1.4
Prusa I3A 2560.zip
(281.17 KiB) Downloaded 5509 times
aluminum I3 sanguinololu
Plusa I3 A sanguinololu.zip
(242.28 KiB) Downloaded 5444 times

[mbeach1116]

Hi, you need to choose to download according to your model and motherboard corresponding type,
Then upload it using Arduino.

I understand that. How do I know which model and motherboard I have?

Hi, your model is i3 aluminum
You need to download it from the corresponding firmware,
Motherboard, you can check your motherboard,
The corresponding model is written on it.

I hope this can help you.

Can you help? Please see message above.

[William]

I understand that. How do I know which model and motherboard I have?

Hi, your model is i3 aluminum
You need to download it from the corresponding firmware,
Motherboard, you can check your motherboard,
The corresponding model is written on it.

I hope this can help you.

Can you help? Please see message above.

you can download this:

CRFNI3Z}D$OY7K3XU`Y56}X.png (36.65 KiB) Viewed 4553924 times

and refer to this to update:viewtopic.php?f=20&t=16433

[mbeach1116]

Hi, your model is i3 aluminum
You need to download it from the corresponding firmware,
Motherboard, you can check your motherboard,
The corresponding model is written on it.

I hope this can help you.

Can you help? Please see message above.

you can download this:CRFNI3Z}D$OY7K3XU`Y56}X.png

and refer to this to update:viewtopic.php?f=20&t=16433

I believe I have updated it. Is there a way to confirm?