Problem usb in the printer

Post Reply
Jmerlos75
Posts: 4
Joined: Mon Jul 29, 2019 7:00 am

Problem usb in the printer

Post by Jmerlos75 » Mon Jul 29, 2019 7:06 am

Hi

I have a problem

Always the USB cable is connected, a reboot is performed :roll: at this moment it is not working

User avatar
William
Site Admin
Posts: 4642
Joined: Tue Jun 07, 2016 9:38 am

Re: Problem usb in the printer

Post by William » Mon Jul 29, 2019 9:34 am

Hi, You can check if your device manager has a corresponding port.
If not, you can try this through:https://www.geeetech.com/download.html?download_id=40
Download the driver for manual installation.
I hope this can help you.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Jmerlos75
Posts: 4
Joined: Mon Jul 29, 2019 7:00 am

Re: Problem usb in the printer

Post by Jmerlos75 » Tue Jul 30, 2019 7:31 am

El problema es que esta deshabilitado el usb y no muestra en administrador de dispositivos el driver a instalar, al comienzo cuando la conecte a la computadora hechaba chispas al tocar el conector en la salida usb, luego se apaga la impresora A20 cuando intentaba conectarla. En este momento la impresora solo funciona con la tarjeta SD, la compre hace menos de un mes por eBay a un vendedor oficial de geentech.
Un detalle es que la impresora la puse a funcionar electricamente en 120 moviendo el switch que trae la maquina.

User avatar
William
Site Admin
Posts: 4642
Joined: Tue Jun 07, 2016 9:38 am

Re: Problem usb in the printer

Post by William » Tue Jul 30, 2019 9:17 am

Hi, Can you provide specific pictures and videos of your question?
You can check your power supply output voltage
and whether your power box is tuned to the safe voltage you need to use.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Jmerlos75
Posts: 4
Joined: Mon Jul 29, 2019 7:00 am

Re: Problem usb in the printer

Post by Jmerlos75 » Tue Jul 30, 2019 10:24 am

adjunto imágenes, yo cambie al botón rojo de la fuente antes de encenderla por primera vez a 115 que es la correspondiente a la salida eléctrica que tengo, algo mas tengo que cambiarle en la maquina, podría usted mostrarme?
Cuando trato de instalar el driver no lo instala ya que no reconoce el USB. La impresora trabaja bien solamente mediante la tarjeta SD. Hasta el momento he probado conectar el USB en 4 computadoras diferentes con el mismo resultado.
Attachments
IMG_20190729_201715.jpg
IMG_20190729_201715.jpg (239.16 KiB) Viewed 2383 times
IMG_20190729_201705.jpg
IMG_20190729_201705.jpg (262.45 KiB) Viewed 2383 times
IMG_20190729_200326.jpg
IMG_20190729_200326.jpg (93.87 KiB) Viewed 2383 times
IMG_20190729_195439.jpg
IMG_20190729_195439.jpg (161.21 KiB) Viewed 2383 times
IMG_20190729_195320.jpg
IMG_20190729_195320.jpg (314.93 KiB) Viewed 2383 times

Jmerlos75
Posts: 4
Joined: Mon Jul 29, 2019 7:00 am

Re: Problem usb in the printer

Post by Jmerlos75 » Tue Jul 30, 2019 10:49 am

Subi un video en el siguiente enlace

https://youtu.be/Egrc4ewQb30

User avatar
_kaktus_
Site Admin
Posts: 1237
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Problem usb in the printer

Post by _kaktus_ » Tue Jul 30, 2019 1:25 pm

:!:

Forum rules - point 6.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

User avatar
William
Site Admin
Posts: 4642
Joined: Tue Jun 07, 2016 9:38 am

Re: Problem usb in the printer

Post by William » Tue Jul 30, 2019 2:43 pm

Hi, You need to download the driver according to your needs.
You can refer to this for specific operations:https://www.geeetech.com/forum/viewtopi ... RlcFtWdCG4
Also, you can try to replace the USB cable to connect to the printer to view.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Jarda3d
Posts: 141
Joined: Sat Jan 26, 2019 8:42 am

Re: Problem usb in the printer

Post by Jarda3d » Mon Nov 04, 2019 7:32 am

Weak mains grounding or bad cable or driver.

Easiest way to reliable install serial drivers for GT printers is to install Arduino IDE.
A10M Slic3r profile: http://www.geeetech.com/forum/viewtopic ... 340#p91340
A10 Slic3r profile: viewtopic.php?f=98&t=69230&p=102310#p102310
>> TIP: tight all screws and wheels (except right side of Z axis) and re-align frame after transportation shocks <<

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest