Search found 362 matches
- Thu Oct 15, 2015 6:12 pm
- Forum: Extruder
- Topic: Geeetech Prusa i3 pro c dual extruder question
- Replies: 6
- Views: 10957
Re: Geeetech Prusa i3 pro c dual extruder question
hi,this is to save space .one fan can cool the 2 extruder at the same time.
- Mon Oct 12, 2015 2:57 pm
- Forum: Firmware
- Topic: How to upload the firmware to Sanguinololu
- Replies: 43
- Views: 216772
Re: How to upload the firmware to Sanguinololu/GT2560
I get a problem with the X axis move in the opposite direction, I follow the instruction shown here ,but i found a issue I can not found the folder mention in the step 6. Open folder "I3_Sanguinololu"(files of Marlin firmware), select all the files (59 in all) and drag them into arduino. I download...
- Thu Oct 01, 2015 10:24 pm
- Forum: Products FAQ
- Topic: DELTA ROSTOK G2S Problem
- Replies: 8
- Views: 11042
Re: DELTA ROSTOK G2S Problem
Good. Tell me then how to configure it . extruder to move parallel to the table ? when X 0 Y0 Z0 -good . when X- 50 Y- 50 Z0- well . at X50 Y- 50 Z0- good. but as soon as X0 Y50 Z0 - bad extruder rises to 3 mm from the table. hi,you need to addjust corresapnding endstop screw.for examle,G0 X0 Y50 Z...
- Thu Oct 01, 2015 10:12 pm
- Forum: Products FAQ
- Topic: MINTEMP on Digital Display
- Replies: 3
- Views: 6571
Re: MINTEMP on Digital Display
Ok new GT2560 board installed and now I have a ERR: MINTEMP on digital display and the printer will not respond to any Repetier - I have checked wiring for both Temp probes and no issues. Need some help please. hi,the mintemp is caused by open circuit in somewhere.could you take a picture to let me...
- Thu Oct 01, 2015 10:06 pm
- Forum: Extruder
- Topic: geeetech prusa I3 x extruder not heating up
- Replies: 4
- Views: 9132
Re: geeetech prusa I3 x extruder not heating up
hi,please see if those three red toward heating cable connector leds are lighted up or not. Manually heat up the hotbed and extruders, if the LED lights under the hotbed and extruder slot are lighted up, then the mosfet that controls the heating is good. next,please measure the resistance of two end...
- Thu Oct 01, 2015 9:57 pm
- Forum: Extruder
- Topic: Prusa I3 X Extruder not working
- Replies: 10
- Views: 30169
Re: Prusa I3 X Extruder not working
hi,please see if there is short circuit in extruder motor pins on those mainboard.
- Thu Oct 01, 2015 9:52 pm
- Forum: Firmware
- Topic: Geeetech Reprap Prusa i3 3D Printer Extruder Firmwar trouble
- Replies: 1
- Views: 4362
Re: Geeetech Reprap Prusa i3 3D Printer Extruder Firmwar tro
hi,you can pull out filament and remove fan in front of fan to see extruder movement more clearly.please clik +10mm or -10mm to test the motor's direction.
- Thu Oct 01, 2015 9:33 pm
- Forum: Firmware
- Topic: compiler errors on unaltered firmware
- Replies: 2
- Views: 5567
Re: compiler errors on unaltered firmware
hi,where did you get the firmware for GT2560? first of all,pelase test the three motors direction.once you start the printer,please test three axis direction by munual control of repetire host.for example,click +10mm in x direction,and clik -10mm as well.in this way,you will know if the motor's dire...
- Thu Oct 01, 2015 7:05 pm
- Forum: Mods And Hacks
- Topic: Mk8 Extruder - filament jams in the throat.
- Replies: 12
- Views: 63351
Re: Mk8 Extruder - filament jams in the throat.
hi,buzmal. how much temperature you set up for extruder?the temperature for pla is 190°-210°.and the gap from nozzle tip to print bed surface is the thickness of an A4 paper.in addition,please see if the filament is place in correct position.it should be along with the groove of the philip screw.
- Wed Sep 30, 2015 4:49 pm
- Forum: Products FAQ
- Topic: home problem
- Replies: 9
- Views: 11973
Re: home problem
hi,maga.do the y still hit the endstop constantly.i do a test,if i connect y endstop cable to x connector on mainbaord.the y will hit endstop constably without stop.please see if the endstop cables connection are correct.