Change the value and try again.....
I can't offer a tutorial here to develop with Arduino or Marlin.
Youtube has many videos on it....
Search found 70 matches
- Thu Aug 30, 2018 12:13 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
- Wed Aug 29, 2018 6:45 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
Re: Geeetech A10 firmware Marlin 1.1.9
It is possible, maybe better using a ATMEGA2560.zonalimitatore wrote: ↑Wed Aug 29, 2018 6:32 pmAnyway...i need to rewrite the bootloader using my arduino uno like programmer,right?
https://www.youtube.com/watch?v=2N1zgX8 ... gs=pl%2Cwn
- Wed Aug 29, 2018 5:50 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
Re: Geeetech A10 firmware Marlin 1.1.9
I do not know if my connections that I know really fit, but you can write to the support to tell you the connections:
https://www.geeetech.com/technical_support.html
https://www.geeetech.com/technical_support.html
- Wed Aug 29, 2018 2:21 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
Re: Geeetech A10 firmware Marlin 1.1.9
You flash the firmware onto your own risk! I mention that everywhere! Disconnecting every machine during flashing can damage the bootloader! First, don't install the version with bootloader included. The bootloader already installed. Look here to load and use the original firmware: http://www.geeete...
- Wed Aug 29, 2018 12:51 am
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
Re: Geeetech A10 firmware Marlin 1.1.9
Perfect.Tonight i try to flash ;) Thanks :mrgreen: Into the menu you found the new setting "manual leveling" To use them klick the wheel down and start the leveling. The A10 now drives 9 points on the heating bed, starting with point 1. Put a piece of paper under the nozzle and turn the wheel up an...
- Tue Aug 28, 2018 7:02 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
Re: Geeetech A10 firmware Marlin 1.1.9
Yes, the configuration is set.
Now you need to leveling your heatbed very precision! After leveling you could print.
Now you need to leveling your heatbed very precision! After leveling you could print.
- Tue Aug 28, 2018 12:39 pm
- Forum: Geeetech A30 Series
- Topic: Adding another extruder for multi material prints
- Replies: 2
- Views: 4836
Re: Adding another extruder for multi material prints
What should be the result?
Multicolorprint or print two workpieces at the same time???
Multicolor: you need to make your own firmware. With A30 it's not easy because the A30 using a 32-bit Controller.
To print multicolor it's better and easier to by the new Geeetech A10M!
Multicolorprint or print two workpieces at the same time???
Multicolor: you need to make your own firmware. With A30 it's not easy because the A30 using a 32-bit Controller.
To print multicolor it's better and easier to by the new Geeetech A10M!
- Tue Aug 28, 2018 12:32 pm
- Forum: Geeetech A30 Series
- Topic: my nozzle has to rub the Geeetech superplate
- Replies: 6
- Views: 9378
Re: my nozzle has to rub the Geeetech superplate
if the bed is well leveld then the nozzle should not touch the bed without filament.
try to keep the printouts out.
You can move the prints in your own slicer to other positions out of the middle.
- Tue Aug 28, 2018 12:19 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10 firmware Marlin 1.1.9
- Replies: 78
- Views: 153758
Re: Geeetech A10 firmware Marlin 1.1.9
Hello everyone... This firm it's ready for install o i need edit config in arduino ide? Or simply click on marlin.ino and upload on board? If you need to change any functions into Marlin you need to use the arduino ide to do it. You can use many ways to install the firmware. two possebilities: 1: A...
- Tue Aug 28, 2018 1:16 am
- Forum: Software
- Topic: I am having problems getting config setting to apply correctly....I think this is the correct place to post this...
- Replies: 8
- Views: 18630
Re: I am having problems getting config setting to apply correctly....I think this is the correct place to post this...
It's difficult! Install cura and select "anycubic i3 Mega" als default Printer from the list of custom printers After that you need to setup the dimensions of the printer manually, because the i3Mega use the dimensions: 210x210x205 (long, width,height) The A30 is bigger. After that you need to level...