Search found 329 matches
- Wed Sep 12, 2018 6:15 pm
- Forum: Geeetech I3 Pro B
- Topic: Printing pauses every half minute, extruder motor overheating?
- Replies: 3
- Views: 5136
- Tue Sep 11, 2018 8:06 pm
- Forum: Geeetech I3 Pro X
- Topic: Geeetech I3X vs Geetech I3 pro X
- Replies: 1
- Views: 7767
Re: Geeetech I3X vs Geetech I3 pro X
Yes, it's the same, it might be a wrong name makes you confuse.
- Tue Sep 11, 2018 7:27 pm
- Forum: Geeetech I3 Pro C
- Topic: Y Axis Problem - step_by_mm
- Replies: 2
- Views: 5338
Re: Y Axis Problem - step_by_mm
Did you edit the max X position value? It seems like the issue comes from firmware.
If you change the bed size, after centering the object, the position will change.
If you change the bed size, after centering the object, the position will change.
- Mon Sep 10, 2018 5:37 pm
- Forum: Geeetech A10 Series
- Topic: A10 auto level sensor
- Replies: 37
- Views: 71742
Re: A10 auto level sensor
For the original version of A10, there is no extension board for hot end and 3D Touch, so it's not that convenient to wire up 3D Touch to the board. Extension wires are needed, and the way for connection is shown as the picture below. This might need some cutting/rewiring and also patience. GT2560 R...
- Wed Sep 05, 2018 5:47 pm
- Forum: Geeetech E180 Mini
- Topic: Firmware upgrade prevents saving of leveling settings (v1.26.36)
- Replies: 17
- Views: 26815
Re: Firmware upgrade prevents saving of leveling settings (v1.26.36)
Upgraded to V1.32.41, also upgraded the UI file, try again, also can save the leveling value.
What is the version of Easyprint that you're using?
Is there the same problem when using other slicer software?
What is the version of Easyprint that you're using?
Is there the same problem when using other slicer software?
- Tue Sep 04, 2018 6:37 pm
- Forum: Geeetech I3 Pro W
- Topic: Conection problem
- Replies: 3
- Views: 5591
Re: Conection problem
Have you set the baud rate to 250000/256000?
- Tue Sep 04, 2018 4:54 pm
- Forum: Geeetech I3 Pro B
- Topic: Lower layer problems + warping
- Replies: 1
- Views: 3695
Re: Lower layer problems + warping
For the gaps:
Try to edit the width value in Repetier host, as default or 110%-120% of the nozzle diameter.
Or set the extrusion multiplier as 1.1.
Calibrate the E step: https://www.youtube.com/watch?v=LzZZaGmeX8w
For the warping:
Try to add Brim.
Try to edit the width value in Repetier host, as default or 110%-120% of the nozzle diameter.
Or set the extrusion multiplier as 1.1.
Calibrate the E step: https://www.youtube.com/watch?v=LzZZaGmeX8w
For the warping:
Try to add Brim.
- Tue Sep 04, 2018 4:22 pm
- Forum: Geeetech A30 Series
- Topic: Home position on the A30, off to front left
- Replies: 4
- Views: 8158
Re: Home position on the A30, off to front left
Try to set up "Bed left" and "Bed front" value (in repetier host) as 5 mm for example, then load the model, center it.
- Mon Sep 03, 2018 6:44 pm
- Forum: Geeetech A30 Series
- Topic: Useful profile / starting GCode to prime extruder
- Replies: 1
- Views: 6141
Re: Useful profile / starting GCode to prime extruder
Thanks for sharing!!
- Mon Sep 03, 2018 6:43 pm
- Forum: Geeetech E180 Mini
- Topic: where to buy power supply for geeetech e180
- Replies: 3
- Views: 7112
Re: where to buy power supply for geeetech e180
We are off duty at weekend, please wait.