Search found 16 matches

by Bs2000
Wed Dec 22, 2021 8:32 pm
Forum: Geeetech I3 M201
Topic: Another edition of the M201 printer firmware for the GTM32Pro vB controller board.
Replies: 3
Views: 22640

Re: Another edition of the M201 printer firmware for the GTM32Pro vB controller board.

so this firmware is from 2019, im sure it is out of testing. How is it working and what changes are there?
by Bs2000
Wed Dec 22, 2021 8:29 pm
Forum: Geeetech I3 M201
Topic: M201 and 3DTouch.
Replies: 6
Views: 10182

Re: M201 and 3DTouch.

Has this yet to be figured out? here we are 4 yrs later and still so limited with the m201
by Bs2000
Mon Jun 24, 2019 9:09 pm
Forum: Geeetech I3 M201
Topic: First print problem
Replies: 11
Views: 16249

Re: First print problem

Kactus thanks, while sometimes it is a little hard to follow, I can understand for the most part. But what I am confused about is that you told me to measure the extruder step and if need be change it to 1mm. I do understand the estep however you said you changed to 101 but your screen shows 9* some...
by Bs2000
Thu Jun 20, 2019 4:33 am
Forum: Geeetech I3 M201
Topic: First print problem
Replies: 11
Views: 16249

Re: First print problem

Measure again, compare it with the line you took earlier. If it's in a good position, you don't have to do anything. Otherwise, in the printer configuration change the number of steps to 1mm for the extruder motor.
by Bs2000
Wed Jun 19, 2019 4:25 am
Forum: Geeetech I3 M201
Topic: First print problem
Replies: 11
Views: 16249

Re: First print problem

Thanks. You didn't mention if that setting was the correct one. Is it the manual extruder speed
by Bs2000
Tue Jun 18, 2019 6:51 pm
Forum: Geeetech I3 M201
Topic: First print problem
Replies: 11
Views: 16249

Re: First print problem

Thanks kaktus, :D would the stepper setting be the manual extruder speed?
by Bs2000
Tue Jun 18, 2019 7:16 am
Forum: Geeetech I3 M201
Topic: First print problem
Replies: 11
Views: 16249

Re: First print problem

Also I have firmware 1.0.0.4 I stalled...
by Bs2000
Tue Jun 18, 2019 4:41 am
Forum: Geeetech I3 M201
Topic: First print problem
Replies: 11
Views: 16249

First print problem

Hi everyone, I finally have my M201 all setup and tested all axis to make sure it runs smoothly. I downloaded a simple sharks tooth file opened it in easyprint3d with all the following settings (see pics) when I slice it and print my filiment comes out at first like string then starts to blob up and...
by Bs2000
Fri May 31, 2019 8:12 pm
Forum: Geeetech I3 M201
Topic: Extruder mount
Replies: 1
Views: 3927

Extruder mount

So when I go to mount the extruders the holes pre drilled leave the bracket setting on a mount screw. Am I doing something wrong?
by Bs2000
Sat May 25, 2019 8:08 pm
Forum: Geeetech I3 M201
Topic: Fan placement
Replies: 5
Views: 6946

Fan placement

So building my M201 and the directions show the fan bolting onto the A1 with a fan cut out behind stepping motor on left side. Well mine doesn't have any cutouts or holes so where do I place fan?