I went out and bought a brand new SD Card which was smaller in size, then formatted it to Fat32 and put the GCode into the Root Directory
Now the LCD Panel is reading the new SD Code.... I am not using the Bigger SD Cards any more
Issue Resolved
Search found 12 matches
- Thu May 04, 2017 10:03 am
- Forum: Control Board
- Topic: SD Card slot not picking up and reading sd cards
- Replies: 7
- Views: 13957
- Thu May 04, 2017 5:53 am
- Forum: Control Board
- Topic: SD Card slot not picking up and reading sd cards
- Replies: 7
- Views: 13957
Re: SD Card slot not picking up and reading sd cards
A update ..... Yes the card formatted to Fat32, I again tried insert the card with no reading, then leaving the card inserted turning off and on the printer, the LCD screen then went to 3 lines of blocks across the whole screen, once I removed the SD card the LCD screen return to normal??
- Wed May 03, 2017 7:47 pm
- Forum: Control Board
- Topic: SD Card slot not picking up and reading sd cards
- Replies: 7
- Views: 13957
Re: SD Card slot not picking up and reading sd cards
I did use Repetier to install the G Code in the main root directory on the SD Card Yes, everything thing else works from the LCD Board to the Printer, so I must have a good connection I am using good quality SD Cards This is where I am not sure, actually what is the FTDI drivers, in me reading about...
- Wed May 03, 2017 6:07 am
- Forum: Control Board
- Topic: SD Card slot not picking up and reading sd cards
- Replies: 7
- Views: 13957
SD Card slot not picking up and reading sd cards
I have the Geeetech Rostock 301 printer, last night is the first time I tried to use a SD card with the printer, I tried 2 separate SD cards and both times the LCD board stated "No SD Card Inserted" both cards are working and I copied the G Code onto them both, but the printer isnt reading the cards...
- Thu Oct 06, 2016 3:48 pm
- Forum: Firmware
- Topic: Can someone actually do photo instruction or YouTube?
- Replies: 2
- Views: 6244
Re: Can someone actually do photo instruction or YouTube?
Ggg666 I can see the instruction regarding the firmware which I am wanting to do, but actually trying the follow the instructions and actually do it at the same time I finding confusing ..... It's actually doing the firmware I would like so watch on YouTube
- Thu Oct 06, 2016 7:58 am
- Forum: Firmware
- Topic: Can someone actually do photo instruction or YouTube?
- Replies: 2
- Views: 6244
Can someone actually do photo instruction or YouTube?
I have purchased a Geeetech Rostock 301 printer from Geeetech I am having hassle digesting all the processes of setting up my printer with the firmware and software I tried to following instructions but in control panel it's says I have a cube 3 printer which is in correct etc etc So I am wondering ...
- Thu Oct 06, 2016 6:34 am
- Forum: Assembly
- Topic: Instructions rostock 301 & No replies from Staff
- Replies: 7
- Views: 14228
Re: Instructions rostock 301 & No replies from Staff
I removed the fan and it still was getting stuck and I couldn't see exactly where, so I removed the extruder from the printer and tried again, until I remove the bottom nozzle from the extruder where the tubing connected to before I was able to feed the filament all the way through the extruder, I c...
- Wed Oct 05, 2016 8:11 pm
- Forum: Assembly
- Topic: Instructions rostock 301 & No replies from Staff
- Replies: 7
- Views: 14228
Re: Instructions rostock 301 & No replies from Staff
what I was trying to explain is that there are 3 extruders which come with the printer, which you are suppose to feed the filament into then the filaments enters the white tubing all the way to the bottom to reach the 3 in 1 hotend. my issue is with the 3 extruders, I am only able to feed filament t...
- Wed Oct 05, 2016 1:47 pm
- Forum: Assembly
- Topic: Heat Sink Instructions
- Replies: 3
- Views: 7814
Re: Heat Sink Instructions
I have now found the answer to my question about the heat sinks plus I went out and spent $2.90 and brought some replacement screws so I was able to finish builder my printer
- Tue Oct 04, 2016 6:38 pm
- Forum: Assembly
- Topic: Instructions rostock 301 & No replies from Staff
- Replies: 7
- Views: 14228
Re: Instructions rostock 301 & No replies from Staff
thank you, I had found where to put the heat sinks from another forum, so that was completed the 3 long leads I was talking about I noticed that you had them removed too, and replaced them with the 3 short leads in your photo that you posted the other issue I am having is regarding those 3 extruders...