Search found 6322 matches

by William
Mon Sep 21, 2020 4:22 pm
Forum: Discuss & Help
Topic: Need help 1st time print
Replies: 1
Views: 55

Re: Need help 1st time print

Hello, are you M series or T series printer? Whether the other extruder also put consumables, this is the test file printed by the dual extruder, you may not put consumables.
Regards.
by William
Mon Sep 21, 2020 4:15 pm
Forum: Control Board
Topic: Geeetech E180 / A30 wifi module Pinouts
Replies: 1
Views: 40

Re: Geeetech E180 / A30 wifi module Pinouts

Hello, if you want to replace the wifi module, please go to the ticket system on the Geeetech official website to consult the after-sales personnel. :D
Regards.
by William
Fri Sep 18, 2020 9:56 am
Forum: Geeetech A30 Series
Topic: First layer problems
Replies: 1
Views: 47

Re: First layer problems

Hello, in response to your question. There are several suggestions: 1.Try to adjust the filament diameter to 1.75mm. 2. Slightly increase the extrusion ratio. 3. Increase the filling percentage. 4. Change to a slicing software, sometimes the printing effect will be significantly improved. 5. You can...
by William
Thu Sep 17, 2020 5:18 pm
Forum: Geeetech A10 Series
Topic: Geeetech A10 Pro doesn't start up
Replies: 1
Views: 45

Re: Geeetech A10 Pro doesn't start up

Hello, maybe there is a problem with your LCD wiring, you can unplug it and reinstall it, and fasten it with a cable tie. You can also try to connect to the computer to see if it can start normally.If possible, please also provide pictures to better solve your problem. :D
Regards
by William
Wed Sep 16, 2020 5:26 pm
Forum: Geeetech A10 Series
Topic: Setting Up Slicer Software For A10M?
Replies: 1
Views: 62

Re: Setting Up Slicer Software For A10M?

Hello, if you want to get the slicing software configuration of A10M, you can log in to the geeetech official website, where there are configuration files for Cura and Repeter-host for download. :D https://www.geeetech.com/download.html?download_id=31 https://www.geeetech.com/download.html?download_...
by William
Wed Sep 16, 2020 10:34 am
Forum: Geeetech A10 Series
Topic: A10 Partcooling fan problem
Replies: 3
Views: 128

Re: A10 Partcooling fan problem

Hello, if you have some questions about pwm fans, you can refer to the following post. :D
viewtopic.php?f=24&t=17886
Regards
by William
Tue Sep 15, 2020 3:09 pm
Forum: Geeetech A10 Series
Topic: A10 Partcooling fan problem
Replies: 3
Views: 128

Re: A10 Partcooling fan problem

Hello, maybe there is something wrong with your fan. If you need to replace the accessories, please consult the Ticket system on the Geeetech official website. :D
Regards
by William
Tue Sep 15, 2020 3:04 pm
Forum: Geeetech A10 Series
Topic: Motherboard voltaje adjustment
Replies: 1
Views: 77

Re: Motherboard voltaje adjustment

Hello, according to the formula, I_TripMax= Vref/(8*Rs) the drive resistance is 0.1Ω, so your current is about 1.5A. :D
Regards
by William
Tue Sep 15, 2020 11:49 am
Forum: Geeetech I3 Pro W
Topic: Extruder problem
Replies: 3
Views: 211

Re: Extruder problem

Hello, you can take a look at the link below, there are very detailed solutions. :D
viewtopic.php?f=19&t=18650
Regards
by William
Mon Sep 14, 2020 5:49 pm
Forum: Geeetech A30 Series
Topic: A30 firmware.
Replies: 31
Views: 28468

Re: A30 firmware.

Hello, you need to download the driver from the link below so that your printer can be recognized by the computer. Afterwards, you can upload the firmware through cura or download the firmware kit. https://www.geeetech.com/download.html?download_id=40 Please download the item of CH340, download the ...