Search found 17 matches
- Wed Sep 30, 2020 2:02 am
- Forum: Geeetech I3 Pro C
- Topic: Latest Firmaware Geeetech I 3 Pro C Dual Head GT2560 A+ with touch
- Replies: 2
- Views: 12539
Re: Latest Firmaware Geeetech I 3 Pro C Dual Head GT2560 A+ with touch
I recently replaced my controller board and loaded in the firmware on my three year old Pro C. I've got a BLTouch that I would like to install but I needed to make sure the printer worked with the new board. I'm interested in what you find out!
- Wed Mar 28, 2018 12:50 am
- Forum: Geeetech I3 Pro C
- Topic: BLTouch Bed Level Sensor & Dual Extruder?
- Replies: 1
- Views: 5405
BLTouch Bed Level Sensor & Dual Extruder?
Are there any tips or tricks to install the BLTouch bed level sensor on a Prusa i3 Pro C dual extruder printer? If that can't be done, what do I need to do to convert the printer to single extruder? I don't do a whole lot of two filament printing. I would like to enjoy the luxury of auto bed levelin...
- Sun Mar 27, 2016 10:49 pm
- Forum: Others
- Topic: X-Axis Belt Comes Loose From Belt Bracket
- Replies: 5
- Views: 10309
Re: X-Axis Belt Comes Loose From Belt Bracket
I was in the middle of printing when it came loose the last time. I inserted a couple of short pieces from a tooth pick to wedge the cogs of the belt into the grooves in the anchor. It has held ever since.
- Sun Feb 07, 2016 5:10 pm
- Forum: Others
- Topic: X-Axis Belt Comes Loose From Belt Bracket
- Replies: 5
- Views: 10309
Re: X-Axis Belt Comes Loose From Belt Bracket
By the way, it's a little too warm back there for hot glue. Looks like it began to melt after finishing a 2 1/2 hour print. It came loose again as the next print began.
- Sun Feb 07, 2016 2:39 am
- Forum: Others
- Topic: X-Axis Belt Comes Loose From Belt Bracket
- Replies: 5
- Views: 10309
X-Axis Belt Comes Loose From Belt Bracket
Hello, I have the acrylic i3 Pro C. I was printing the other day and the x-axis belt came loose from the blue plastic bracket on one end. I pulled it tight enough for some moderate tension and slid it in. I'm not sure how many prints I've attempted since then, but it came loose twice today. The belt...
- Thu Jan 28, 2016 8:30 am
- Forum: Others
- Topic: Warped heatbed problem
- Replies: 8
- Views: 17142
Re: Warped heatbed problem
How thick of a piece of glass did you use and where did you obtain it? I have an Acrylic Pro C dual extruder and the bed of mine with the glass is considerably higher in the center than the corners and edges. I was adjusting my print nozzle to bed distance at the edges and found that adjusting it to...
- Wed Jan 27, 2016 7:46 pm
- Forum: Print Quality
- Topic: Two Color Printing Alignment
- Replies: 3
- Views: 7747
Re: Two Color Printing Alignment
Would that go to something like -17/+15? Do they always need to be 32 mm apart or might that value need to be changed to something else (to something like -18/16)?
Thanks.
Thanks.
- Tue Jan 26, 2016 6:52 am
- Forum: Print Quality
- Topic: ABS Adhesion and Corner Lifting
- Replies: 7
- Views: 16102
Re: ABS Adhesion and Corner Lifting
This has been sort of solved. I still have issues around the perimeter of the bed, but things are sticking much better now. Via email to my seller, who forwarded my issue, I conferred with Eric at Geeetech who was extremely helpful. I also found that the glass bed is bowed upward near the center by ...
- Tue Jan 26, 2016 6:36 am
- Forum: Print Quality
- Topic: Two Color Printing Alignment
- Replies: 3
- Views: 7747
Two Color Printing Alignment
I managed to make it through most of my adhesion issues and I thank Mark and everyone else for your suggestions and assistance. Since single color color printing seems to work at an acceptable ratio of yay/fails, I figured I'd venture into two color printing. Per the user manual for the Pro C dual e...
- Wed Jan 20, 2016 7:38 am
- Forum: Print Quality
- Topic: ABS Adhesion and Corner Lifting
- Replies: 7
- Views: 16102
Re: ABS Adhesion and Corner Lifting
Please do not misinterpret this as being confrontational. That said, I don't feel that limiting the printer to PLA would be a good idea from at least a couple of aspects. This printer is sold as being capable of printing ABS and I'm sure that others have done so with very good results. If that were ...