HI Friend:
If only power 5 volts,that's ok.Don't worry.
Best regards.
Search found 77 matches
- Tue Mar 04, 2014 7:27 pm
- Forum: Project Talent Show
- Topic: powering the sim900 via non arduino mcu
- Replies: 2
- Views: 9810
- Tue Mar 04, 2014 2:51 pm
- Forum: Others
- Topic: Pinout for Mechanical End Stop Endstop Switch Module V1.2
- Replies: 2
- Views: 11682
Re: Pinout for Mechanical End Stop Endstop Switch Module V1.
HI Friend:
Sorry for my late reply!
The pin from top to bottom is :COM,NO,NO,NC.If you can't understand,click the link.http://www.thingiverse.com/thing:762
Sorry for my late reply!
The pin from top to bottom is :COM,NO,NO,NC.If you can't understand,click the link.http://www.thingiverse.com/thing:762
- Tue Mar 04, 2014 1:53 pm
- Forum: Project Talent Show
- Topic: software power the sim900 via software
- Replies: 2
- Views: 9840
Re: software power the sim900 via software
HI Friend:
The GPRS shield can't work without an Arduino
The GPRS shield can't work without an Arduino
- Tue Mar 04, 2014 11:18 am
- Forum: Control Board
- Topic: Melzi won't connect to PC
- Replies: 1
- Views: 7889
Re: Melzi won't connect to PC
Hi friend:
1.You can put the jumper cap plug in the USB interface
2.If prompted to install the driver is good,but need to replace the FT232
1.You can put the jumper cap plug in the USB interface
2.If prompted to install the driver is good,but need to replace the FT232
- Mon Mar 03, 2014 6:09 pm
- Forum: Project Talent Show
- Topic: 9 DOF weird data readings
- Replies: 1
- Views: 7656
Re: 9 DOF weird data readings
HI friend:
You can enter the serial monitor, and then change the baud rate is 115200
You can enter the serial monitor, and then change the baud rate is 115200
- Wed Dec 04, 2013 3:47 pm
- Forum: Control Board
- Topic: Melzi Ardentissimo Failure
- Replies: 13
- Views: 33326
Re: Melzi Ardentissimo Failure
According to the figure, weld the plate connected, and then download code from the official website .
- Tue Dec 03, 2013 11:40 am
- Forum: Project Talent Show
- Topic: HY-280-262k compatability with ATmega1281
- Replies: 10
- Views: 25134
Re: HY-280-262k compatability with ATmega1281
I am sorry .we are very busy.but you can refer to the link:http://www.geeetech.com/wiki/index.php/2.8%22TFT_LCD
and write library by yourself.
and write library by yourself.
- Mon Dec 02, 2013 11:15 am
- Forum: Control Board
- Topic: gen6 unresponsive
- Replies: 11
- Views: 21654
Re: gen6 unresponsive
Hi
I am so sorry.but you can download firmware from WIKI now
I am so sorry.but you can download firmware from WIKI now
- Mon Dec 02, 2013 8:57 am
- Forum: Project Talent Show
- Topic: HY-280-262k compatability with ATmega1281
- Replies: 10
- Views: 25134
Re: HY-280-262k compatability with ATmega1281
hi
Friend .you can use 1281 to control it.but you must create head file by yourself.
Friend .you can use 1281 to control it.but you must create head file by yourself.
- Thu Nov 28, 2013 5:38 pm
- Forum: Control Board
- Topic: Printrboard trace burn
- Replies: 15
- Views: 30093
Re: Printrboard trace burn
Your power supply can be used,please potentiometer reference voltage to 1.0 v.and the com port disconnected suddenly?